View SY54017R_5227414.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SY54017R low voltage 1.2v/1.8v cml 2:1 mux with fail safe inputs, 3.2gbps, 2.5ghz precision edge is a registered trademark of micrel, inc. mlf is a registered trademark of amkor technology, inc. micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com march 2008 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 general description the SY54017R is a fully differential, low voltage 1.2v/1.8v cml 2:1 mux with fail safe inputs. the SY54017R can process clock sig nals as fast as 2.5ghz or data patterns up to 3.2gbps. the differential input includes micrel?s unique, 3-pin input termination architecture that interfaces to lvpecl, lvds or cml differential signals, (ac- or dc-coupled from a 2.5v driver) as small as 100mv (200mv pp ) without any level-shifting or termination resistor networks in the signal pat h. for ac-coupled input interface applications, an internal voltage reference is provided to bias the v t pin. the outputs are cml, with extremely fast rise/fall times guaranteed to be less than 95ps. the SY54017R operates from a 2.5v 5% core supply and a 1.8v or 1.2v 5% output supply and is guaranteed over the full industrial temperature range (?40c to +85c). the SY54017R is part of micrel?s high-speed, precision edge ? product line. datasheets and support documentation can be found on micrel?s web site at: www.micrel.com . functional block diagram precision edge ? features ? 1.2v/1.8v cml 2:1 mux with fail safe inputs ? guaranteed ac performance over temperature and voltage: ? dc-to- > 3.2gbps throughput ? <390ps propagation delay (in-to-q) ? <20ps input-to-input skew ? <95ps rise/fall times ? ultra-low jitter design ? <1ps rms cycle-to-cycle jitter ? <10ps pp total jitter ? <1ps rms random jitter ? <10ps pp deterministic jitter ? high-speed cml outputs ? 2.5v 5% , 1.8/1.2v 5% power supply operation ? industrial temperature range: ?40c to +85c ? available in 16-pin (3mm x 3mm) mlf ? package applications ? data distribution: oc-48, oc-48+fec ? sonet clock and data distribution ? fibre channel clock and data distribution ? gigabit ethernet clock and data distribution markets ? storage ? ate ? test and measurement ? enterprise networking equipment ? high-end servers ? access ? metro area network equipment
micrel, inc. SY54017R march 2008 2 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 ordering information (1) part number package type operating range package marking lead finish SY54017Rmg mlf-16 industrial 017r with pb-free bar-line indicator nipdau pb-free SY54017Rmgtr (2) mlf-16 industrial 017r with pb-free bar-line indicator nipdau pb-free notes: 1. contact factory for die availability. dice are guaranteed at t a = 25c, dc electricals only. 2. tape and reel. pin configuration 16-pin mlf ? (mlf-16)
micrel, inc. SY54017R march 2008 3 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 pin description pin number pin name pin function 16,1 4,5 in0, /in0 in1,/in1 differential inputs: these input pairs are th e differential signal inputs to the device. they accept differential signals as small as 100mv (200mv pp ). each input pin internally terminates with 50 ? to the vt pin. if the input swing falls below a certain threshold (typical 30mv), the fail safe i nput (fsi) feature w ill guarantee a stable output by latching the output to its last valid state. 2 3 vt0 vt1 input termination center-tap: each side of t he differential input pair terminates to a vt pin. this pin provides a center-tap to a termination network for maximum interface flexibility. an internal high impedance resistor divider biases vt to allow input ac coupling. for ac-coupling, bypass vt with a 0.1f low esr capacitor to vcc. see ?interface applications? subsection and figure 2a. 15 sel this single-ended ttl/cmos compatible inpu t selects the inputs to the multiplexer. note that this input is internally connected to a 25k ohm pull-up resistor and will default to a logic high state if left open. 7 vcc positive power supply: bypass with 0.1uf//0.01uf low esr capacitors as close to the v cc pin as possible. supplies input and core circuitry. 8,13 vcco output supply: bypass with 0.1uf//0.01uf low esr capacitors as close to the v cco pins as possible. supplies the output buffer. 14 gnd, exposed pad ground: exposed pad must be connected to a ground plane that is the same potential as the ground pin. 11,10 q, /q cml differential output pair: differential buffered copy of the input signal. the output swing is typically 390mv. see ?i nterface applications? subsection for termination information. truth table sel output 0 in0 input selected 1 in1 input selected
micrel, inc. SY54017R march 2008 4 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 absolute maximum ratings (1) supply voltage (v cc ) ............................... ?0.5v to +3.0v supply voltage (v cco ) ............................. ?0.5v to +2.7v v cc ? v cco ........................................................<1.8v v cco ? v cc ........................................................<0.5v input voltage (v in ) .......................................?0.5v to v cc cml output voltage (v out ) ............... 0.6v to v cco +0.5v current (v t ) source or sink current on vt pin .................100ma input current source or sink current on (in, /in).................50ma maximum operating junc tion temperature .......... 125c lead temperature (solde ring, 20sec .) .................. 260c storage temperature (t s ) ....................?65c to +150c operating ratings (2) supply voltage (v cc )..........................2.375v to 2.625v (v cco )??????...?..1.14v to 1.9v ambient temperature (t a ) ................... ?40c to +85c package thermal resistance (3) mlf ? still-air ( ja ) ............................................ 75c/w junction-to-board ( jb ) .......................... 33c/w dc electrical characteristics (4) t a = ?40c to +85c, unless otherwise stated. symbol parameter condition min typ max units v cc power supply voltage range v cc v cco v cco 2.375 1.14 1.7 2.5 1.2 1.8 2.625 1.26 1.9 v v v i cc power supply current max. v cc 22 32 ma i cco power supply current no load. max v cco 16 21 ma r in input resistance (in-to-v t , /in-to-v t ) 45 50 55 ? r diff_in differential input resistance (in-to-/in) 90 100 110 ? v ih v il input high voltage (in, /in) input low voltage (in, /in) in, /in v il with v ih = 1.2v 1.2 0.2 v cc v ih ?0.1 v v v ih v il input high voltage (in, /in) input low voltage (in, /in) in, /in v il with v ih = 1.14v, (1.2v-5%) 1.14 0.66 v cc v ih ?0.1 v v v in input voltage swing (in, /in) see figure 3a 0.1 1.0 v v diff_in differential input voltage swing (|in - /in|) see figure 3b 0.2 2.0 v v in_fsi input voltage threshold that triggers fsi 30 100 mv v t_in voltage from input to v t 1.28 v notes: 1. permanent device damage may occur if absolute maximum ratings are exceeded. this is a stress rating only and functional ope ration is not implied at conditions other than those deta iled in the operational sections of this data sheet. exposure to absolute maximum ra tings conditions for extended periods may affect device reliability. 2. the data sheet limits are not guaranteed if t he device is operated beyond the operating ratings. 3. package thermal resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the pc b. jb and ja values are determined for a 4-layer board in still-air number, unless otherwise stated. 4. the circuit is designed to meet the dc specifications shown in the above table after thermal equilibrium has been establishe d.
micrel, inc. SY54017R march 2008 5 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 cml outputs dc electrical characteristics (5) v cco = 1.14v to 1.26v r l = 50 ? to v cco, v cco = 1.7v to 1.9v, r l = 50 ? to v cco or 100 ? across the outputs, v cc = 2.375v to 2.625v. t a = ?40c to +85c, unless otherwise stated. symbol parameter condition min typ max units v oh output high voltage r l = 50 ? to v cco v cco -0.020 v cco -0.010 v cco v v out output voltage swing see figure 3a 300 390 475 mv v diff_out differential output voltage swing see figure 3b 600 780 950 mv r out output source impedance 45 50 55 ? lvttl/cmos dc electri cal characteristics (5) v cc = 2.5v 5%; v cco = +1.14v to +1.26v or +1.7v to +1.9v; t a = ?40c to +85c, unless otherwise stated. symbol parameter condition min typ max units v ih input high voltage 2.0 v cc v v il input low voltage 0.8 v i ih input high current - 125 30 a i il input low current -300 a note: 5. the circuit is designed to meet the dc specifications shown in the above table after thermal equilibrium has been establishe d.
micrel, inc. SY54017R march 2008 6 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 ac electrical characteristics v cco = 1.14v to 1.26v r l = 50 ? to v cco, v cco = 1.7v to 1.9v, r l = 50 ? to v cco or 100 ? across the outputs, v cc = 2.375v to 2.625v. t a = ?40c to +85c, unless otherwise stated. symbol parameter condition min typ max units nrz data 3.2 gbps f max maximum frequency v out > 200mv clock 2.5 ghz v in : 100mv-200mv, note 6, figure 1a 220 320 470 ps v in : >200mv, note 6, figure 1a 190 270 390 ps t pd propagation delay in-to-q sel-to-q see figure 1a 90 200 350 ps input-to-input skew note 8 5 20 ps t skew part-to-part skew note 9 75 ps note 10 1 ps rms data random jitter deterministic jitter note 11 10 ps pp note 12 1 ps rms note 13 10 ps pp t jitter clock cycle-to-cycle jitter total jitter crosstalk induced jitter (adjacent channel) note 14 0.7 ps pp t r t f output rise/fall times (20% to 80%) at full output swing. 30 60 95 ps duty cycle differential i/o 47 53 % notes: 6. propagation delay is measured with input t r /t f 300ps (20% to 80%). 8. input-to-input skew is the difference in time between both inputs and the output for the same temperature, voltage and trans ition. 9. part-to-part skew is defined for two parts with identical pow er supply voltages at the same temperature and no skew at the e dges at the respective inputs. vin >200mv with input t r /t f 300ps (20% to 80%). 10. random jitter is measured with a k28.7 pattern, measured at f max . 11. deterministic jitter is measur ed at 2.5gbps with both k28.5 and 2 23 ?1 prbs pattern. 12. cycle-to-cycle jitter definition: the variation period between adjacent cycles over a random sample of adjacent cycle pairs . t jitter _ cc = t n ?t n+1 , where t is the time between rising edges of the output signal. 13. total jitter definition: with an ideal clock input frequency of f max (device), no more than one output edge in 10 12 output edges will deviate by more than the specified peak -to-peak jitter value. 14. crosstalk induced jitter is defined as the added jitter that results from si gnals applied to the adjacent channel. it is measured at the output while applying a similar, differential clock frequencies that are asynch ronous with respect to each other at the adjacent input.
micrel, inc. SY54017R march 2008 7 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 functional description fail-safe input (fsi) the input includes a special failsafe circuit to sense the amplitude of the input signal and to latch the output when there is no input signal present, or when the amplitude of the input signal drops sufficiently below 100mv pk (200mv pp ), typically 30mv pk . maximum frequency of the SY54017R is limited by the fsi function. input clock failure case if the input clock fails to a fl oating, static, or extremely low signal swing, the fsi function will eliminate a metastable condition and guarantee a stable output. no ringing and no undetermi ned state will occur at the output under these conditions. note that the fsi function will not prevent duty cycle distortion in case of a sl owly deteriorating (but still toggling) input signal close to the fsi threshold. due to the fsi function, the propagation delay will depend on rise and fall time of the input signal and on its amplitude. refer to ?typical characteristics? for detailed information interface applications for input interface applications, see figures 4a-f and for cml output termination, see figures 5a-d. cml output termination with vcco 1.2v for vcco of 1.2v, figure 5a, terminate the output with 50 ? -to-1.2v, dc-coupled, not 100 ? differentially across the outputs. if ac-coupling is used, figure 5d, terminate into 50 ? to 1.2v before the coupling capacitor and then connect to a high value resistor to a reference voltage. do not ac couple with internally terminated receiver. for example, 50 ? any-in input. ac-coupling will offset the output voltage by 200mv and this offset voltage will be too low for proper driver operation. cml output termination with vcco 1.8v for vcco of 1.8v, figure 5a and figure b, terminate with either 50 ? -to-1.8v or 100 ? differentially across the outputs. ac- or dc-coupling is fine. input ac-coupling the SY54017R input can accept ac-coupling from any driver. bypass vt with a 0.1f low esr capacitor to vcc as shown in figures 4c and 4d. vt has an internal high impedance resistor divider as shown in figure 2a, to provide a bias voltage for ac-coupling.
micrel, inc. SY54017R march 2008 8 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 timing diagrams figure 1a. propagation delay figure 1b. fail safe feature
micrel, inc. SY54017R march 2008 9 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 typical characteristics v cc = 2.5v, v cco =1.2v gnd = 0v, v in = 100mv, r l = 50 ? to 1.2v, t a = 25c, unless otherwise stated.
micrel, inc. SY54017R march 2008 10 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 functional characteristics v cc = 2.5v, v cco =1.2v gnd = 0v, v in = 400mv, r l = 50 ? to 1.2v, data pattern: 2 23 -1, t a = 25c, unless otherwise stated.
micrel, inc. SY54017R march 2008 11 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 functional characteristics v cc = 2.5v, v cco =1.2v gnd = 0v, v in = 400mv, r l = 50 ? to 1.2v, t a = 25c, unless otherwise stated.
micrel, inc. SY54017R march 2008 12 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 input and output stage figure 2a. simplified differential input buffer figure 2b. simplified cml output buffer single-ended and di fferential swings figure 3a. single-ended swing figure 3b. differential swing
micrel, inc. SY54017R march 2008 13 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 input interface applications figure 4a. cml interface (dc-coupled, 1.8v, 2.5v) figure 4b. cml interface (dc-coupled, 1.2v) figure 4c. cml interface (ac-coupled) figure 4d. lvpecl interface (ac-coupled) figure 4e. lvpecl interface (dc-coupled) figure 4f. lvds interface
micrel, inc. SY54017R march 2008 14 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 cml output termination figure 5a. 1.2v or 1.8v cml dc-coupled termination figure 5b. 1.8v cml dc-coupled termination figure 5c. cml ac-coupled termination (v cco 1.8v only) figure 5d. cml ac-coupled termination (v cco 1.2v only) related product and support documents part number function datasheet link sy54017ar 3.2gbps precision, 2:1 lo w voltage cml mux with internal termination http://www.micrel.com/page.do?page=/product- info/products/sy54017ar.shtml hbw solutions new products and termination application notes http://www.micrel.com/page.do?page=/product- info/as/hbwsolutions.shtml
micrel, inc. SY54017R march 2008 15 m9999-033108-a hbwhelp@micrel.com or (408) 955-1690 package information 16-pin mlf ? (3mm x3mm) (mlf-16) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is belie ved to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and specificati ons at any time without notification to the customer. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. li fe support devices or systems are devices or systems that (a ) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to resul t in a significant injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support applianc es, devices or systems is a pu rchaser?s own risk and purchaser agrees to fully indemnify micrel fo r any damages resulting from such use or sale. ? 2008 micrel, incorporated.

▲Up To Search▲

Price & Availability of SY54017R

	To Download SY54017R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .